Sistema de Gestão de Rede

Solicito apoio técnico para verificação de alarme no ACCID Dados (Circuito): "N/A" com a falha de "Tipo de Falha: Link Down". O circuito começa em (Roteador A (Origem): RNACBSA-DF0719-01 - TenGigE0/0/0/16. Status: UP, Fabricante: HUAWEI, Alarme Ativo: HIGH ERROR RATE) indo ate (Roteador B (Destino): RNACBSA-DF1912-01 - TE0/0/0/17. Status: UP, Fabricante: HUAWEI, Alarme Ativo: N/A). Onde a rota física passa por (ROTA FÍSICA (ELEMENTOS TX UTILIZADOS)): Não informada Informações Extras / Rascunho: High error rate RNACBSA-DF0719-01 - TenGigE0/0/0/16 02/02/26 17:25:49 TenGigE0/0/0/16 CONEXAO AO ACC|RNACBSA-DF1912-01 - TE0/0/0/17|NONE|ACC BSA008|ACT|NONE RP/0/RP0/CPU0:RNACBSA-DF0719-01#show interfaces TenGigE0/0/0/16 Mon Feb 2 23:38:06.835 -03 TenGigE0/0/0/16 is up, line protocol is up Interface state transitions: 1 Dampening enabled: penalty 0, not suppressed half-life: 1 reuse: 750 suppress: 2000 max-suppress-time: 4 restart-penalty: 0 Hardware is TenGigE, address is ac4a.67d4.0e14 (bia ac4a.67d4.0e14) Description: CONEXAO AO ACC|RNACBSA-DF1912-01|TE0/0/0/17|NONE|ACC BSA008|ACT|NONE Internet address is Unknown MTU 9100 bytes, BW 10000000 Kbit (Max: 10000000 Kbit) reliability 255/255, txload 0/255, rxload 0/255 Encapsulation ARPA, Full-duplex, 10000Mb/s, ZR, link type is force-up output flow control is off, input flow control is off Carrier delay (up) is 16 msec loopback not set, Last link flapped 06:30:36 Last input 00:00:00, output 00:00:00 RP/0/RP0/CPU0:RNACBSA-DF0719-01#show controllers TenGigE0/0/0/16 Mon Feb 2 23:38:53.429 -03 Operational data for interface TenGigE0/0/0/16: State: Administrative state: enabled Operational state: Up LED state: Green On Phy: Media type: Cisco-defined, over 1550nm optics Optics: Vendor: CISCO-SUMITOMO Part number: SPP5110ZR-C1 Serial number: SPC234400R9 Wavelength: 1550 nm Digital Optical Monitoring: Transceiver Temp: 31.000 C Transceiver Voltage: 3.279 V Alarms key: (H) Alarm high, (h) Warning high (L) Alarm low, (l) Warning low Wavelength Tx Power Rx Power Laser Bias Lane (nm) (dBm) (mW) (dBm) (mW) (mA) -- ----- ------ ------ ------ ------ ------ 0 n/a 2.2 1.6560 -17.4 0.0183 52.854 ==========> DEGRADACAO, THESHOLD É -7 DOM alarms: No alarms Alarm Alarm Warning Warning Alarm Thresholds High High Low Low ------- ------- ------- ------- Transceiver Temp (C): 75.000 70.000 0.000 -5.000 Transceiver Voltage (V): 3.630 3.465 3.135 2.970 Laser Bias (mA): 120.000 112.000 20.000 17.000 Transmit Power (mW): 5.012 2.512 1.000 0.398 Transmit Power (dBm): 7.000 4.000 0.000 -4.000 Receive Power (mW): 0.501 0.200 0.002 0.001 Receive Power (dBm): -3.000 -7.001 -27.212 -30.969 RP/0/RP0/CPU0:RNACBSA-DF1912-01#show interfaces TE0/0/0/17 Mon Feb 2 23:40:03.809 -03 TenGigE0/0/0/17 is up, line protocol is up Interface state transitions: 103 Dampening enabled: penalty 0, not suppressed half-life: 1 reuse: 750 suppress: 2000 max-suppress-time: 4 restart-penalty: 0 Hardware is TenGigE, address is 40f0.78d5.6b15 (bia 40f0.78d5.6b15) Description: CONEXAO AO ACC|RNACBSA-DF0719-01|TE0/0/0/16|NONE|ACC BSA008|ACT|NONE Internet address is Unknown MTU 9100 bytes, BW 10000000 Kbit (Max: 10000000 Kbit) reliability 255/255, txload 0/255, rxload 0/255 Encapsulation ARPA, Full-duplex, 10000Mb/s, ER, link type is force-up output flow control is off, input flow control is off Carrier delay (up) is 16 msec loopback not set, Last link flapped 06:32:33 Last input 00:00:00, output 00:00:00 RP/0/RP0/CPU0:RNACBSA-DF1912-01#show controllers TE0/0/0/17 Mon Feb 2 23:40:28.545 -03 Operational data for interface TenGigE0/0/0/17: State: Administrative state: enabled Operational state: Up LED state: Green On Phy: Media type: R fiber over 1550nm optics Optics: Vendor: CISCO-FINISAR Part number: FTLX1672D3BCL-C4 Serial number: FNS23200LF5 Wavelength: 1550 nm Digital Optical Monitoring: Transceiver Temp: 34.000 C Transceiver Voltage: 3.304 V Alarms key: (H) Alarm high, (h) Warning high (L) Alarm low, (l) Warning low Wavelength Tx Power Rx Power Laser Bias Lane (nm) (dBm) (mW) (dBm) (mW) (mA) -- ----- ------ ------ ------ ------ ------ 0 n/a 0.1 1.0184 -12.4 0.0569 91.928 DOM alarms: No alarms Alarm Alarm Warning Warning Alarm Thresholds High High Low Low ------- ------- ------- ------- Transceiver Temp (C): 75.000 70.000 0.000 -5.000 Transceiver Voltage (V): 3.630 3.465 3.135 2.970 Laser Bias (mA): 125.000 120.000 55.000 50.000 Transmit Power (mW): 5.012 2.512 0.339 0.135 Transmit Power (dBm): 7.000 4.000 -4.701 -8.703 Receive Power (mW): 1.585 0.794 0.026 0.011 Receive Power (dBm): 2.000 -1.000 -15.817 -19.788

Solicito apoio técnico para verificação de alarme no ACCID Dados (Circuito): "N/A" com a falha de "Tipo de Falha: Link Down". O circuito começa em (Roteador A (Origem): RNAGSPO-SPCD06-01. Status: UP, Fabricante: HUAWEI, Alarme Ativo: THE NUMBER OF MPUS IN A FRAME DOES NOT MEET THE FULL CONFIGURATION)(Destino: Ponta única/Cliente/Nuvem). Onde a rota física passa por (ROTA FÍSICA (ELEMENTOS TX UTILIZADOS)): Não informada Informações Extras / Rascunho: The Number of MPUs in a Frame Does Not Meet the Full Configuration RNAGSPO-SPCD06-01 02/02/26 22:15:01

Solicito apoio técnico para verificação de alarme no ACCID Dados (Circuito): "N/A" com a falha de "Tipo de Falha: Link Down". O circuito começa em (Roteador A (Origem): RNACDQX-RJ2759-01 - 1/1/18. Status: UP, Fabricante: NOKIA, Alarme Ativo: DDMTXBIASCURRENTLOWALARM) indo ate (Roteador B (Destino): RNACDQX-RJ2783-01 - 1/1/17. Status: UP, Fabricante: NOKIA, Alarme Ativo: N/A). Onde a rota física passa por (ROTA FÍSICA (ELEMENTOS TX UTILIZADOS)): Não informada Informações Extras / Rascunho: DDMTxBiasCurrentLowAlarm RNACDQX-RJ2759-01 - 1/1/18 02/02/26 15:30:19 Port 1/1/18-ddm CONEXAO ENTRE RNACDQX-RJ2783-01 - 1/1/17 E RNACDQX-RJ2759-01 - 1/1/18, COM -40 EM RNACDQX-RJ2783-01 - 1/1/17 RNACDQX-RJ2759-01 : DDMTxBiasCurrentLowAlarm : Port 1/1/18-ddm : Nokia_NSP_Kafka : NOKIA_NSP : 1 A:RNACDQX-RJ2759-01# show port 1/1/18 =============================================================================== Ethernet Interface =============================================================================== Description : CONEXAO AO ACC|RNACDQX-RJ2783-01|TE1/1/17|ACC|RJO168|ACT| NONE Interface : 1/1/18 Oper Speed : 10 Gbps Link-level : Ethernet Config Speed : 10 Gbps Admin State : up Oper Duplex : full Oper State : up Config Duplex : N/A Physical Link : Yes MTU : 9208 Single Fiber Mode : No Min Frame Length : 64 Bytes Loopback Mode : none Loopback SwapMac : No IfIndex : 1610891408 Hold time up : 5 seconds Last State Change : 01/20/2026 06:20:11 Hold time down : 5 seconds Last Cleared Time : N/A DDM Events : Enabled Phys State Chng Cnt: 1 RS-FEC Config Mode : None =============================================================================== Transceiver Digital Diagnostic Monitoring (DDM), Internally Calibrated =============================================================================== Value High Alarm High Warn Low Warn Low Alarm ------------------------------------------------------------------------------- Temperature (C) +0.0 +95.0 +90.0 -45.0 -50.0 Supply Voltage (V) 0.00 3.60 3.55 3.05! 3.00! Tx Bias Current (mA) 0.0 95.0 90.0 5.0! 3.0! Tx Output Power (dBm) -40.00 3.50 2.50 -10.20! -11.20! Rx Optical Power (oma dBm) -40.00 3.50! 2.50! -16.40 -17.40 =============================================================================== A:RNACDQX-RJ2783-01# show port 1/1/17 =============================================================================== Ethernet Interface =============================================================================== Description : CONEXAO AO ACC|RNACDQX-RJ2759-01|TE1/1/18|ACC|RJO168|ACT| NONE Interface : 1/1/17 Oper Speed : 10 Gbps Link-level : Ethernet Config Speed : 10 Gbps Admin State : up Oper Duplex : full Oper State : up Config Duplex : N/A Physical Link : Yes MTU : 9208 Single Fiber Mode : No Min Frame Length : 64 Bytes Loopback Mode : none Loopback SwapMac : No IfIndex : 1610891400 Hold time up : 5 seconds Last State Change : 01/20/2026 06:20:11 Hold time down : 5 seconds Last Cleared Time : N/A DDM Events : Enabled =============================================================================== Transceiver Digital Diagnostic Monitoring (DDM), Internally Calibrated =============================================================================== Value High Alarm High Warn Low Warn Low Alarm ------------------------------------------------------------------------------- Temperature (C) +57.1 +95.0 +90.0 -45.0 -50.0 Supply Voltage (V) 3.20 3.60 3.55 3.05 3.00 Tx Bias Current (mA) 42.4 95.0 90.0 5.0 3.0 Tx Output Power (dBm) -2.40 3.50 2.50 -10.20 -11.20 Rx Optical Power (avg dBm) -8.72 3.50 2.50 -16.40 -17.40 =============================================================================== ===============================================================================

Atenuação entre "PARAISO DO TOCANTINS-TO" para "PALMAS-TO". (ANEL: WDM_LD_CS_SECAO_L) ELEMENTO 1: PIT-JPA01-CSW01 - LINE-1-7-3-RX&LINE-1-7-3-TX ELEMENTO 2: PMJ-ROD01-CSW01 - LINE-1-2-3-RX&LINE-1-2-3-TX Alarme Elemento 1: LOS-O Alarmes Elemento Vizinho: LOS-O ACCID/LC: Não informado. Swap de Fibra: VIVO - Protocolo anterior - ABR 116606 Informações extras: . CHANNEL Span Loss (PIT-JPA01-CSW01 to PMJ-ROD01-CSW01) 25.9 dB Measurement Type: CHANNEL Min Threshold(dB): 20 Max Threshold(dB): 24 Resolution(dB): 2.5 x CHANNEL Span Loss (PMJ-ROD01-CSW01 to PIT-JPA01-CSW01) 26.9 dB Measurement Type: CHANNEL Min Threshold(dB): 20 Max Threshold(dB): 24 Resolution(dB): 2.5 PMJ-ROD01-CSW01 LINE-1-2-3-RX&LINE-1-2-3-TX 16.7 dBm -9.6 dBm x PIT-JPA01-CSW01 LINE-1-7-3-RX&LINE-1-7-3-TX 16.4 dBm -10.2 dB --- Regra do Teste OTDR --- Teste OTDR em curso: Nao. Acionado equipe SOM. Próxima atualização às: 00:17.